Hallo,
mein RPI fährt jetzt wieder hoch. Ich habe den Split 128 GPU
Und 128 CPU.
Mein Problem:
Eigentlich hat der CPU irgendwas mit 300.(Wegen 512mb RAM)
Kann mir jemand helefen?
Raspberry Pi mit 512MB RAM - Firmware Update
-
Math2002 -
22. Oktober 2012 um 15:41 -
Geschlossen -
Erledigt
Heute ist Stammtischzeit:
Jeden Donnerstag 20:30 Uhr hier im Chat.
Wer Lust hat, kann sich gerne beteiligen. ;)
Jeden Donnerstag 20:30 Uhr hier im Chat.
Wer Lust hat, kann sich gerne beteiligen. ;)
-
-
Raspberry Pi mit 512MB RAM - Firmware Update? Schau mal ob du hier fündig wirst!
-
Also ich bekomme das nicht hin bei mir wird 256 angezeigt oder liege ich da falsch hier mal die info:
Processor : ARMv6-compatible processor rev 7 (v6l)
BogoMIPS : 795.44
Features : swp half thumb fastmult vfp edsp java tls
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xb76
CPU revision : 7Hardware : BCM2708
Revision : 000f
Serial : xxxxxxxxxxxxxxxxMemTotal: 254860 kB
MemFree: 158056 kB
Buffers: 7168 kB
Cached: 39380 kB
SwapCached: 0 kB
Active: 48840 kB
Inactive: 38956 kB
Active(anon): 41248 kB
Inactive(anon): 460 kB
Active(file): 7592 kB
Inactive(file): 38496 kB
Unevictable: 0 kB
Mlocked: 0 kB
SwapTotal: 124924 kB
SwapFree: 124924 kB
Dirty: 64 kB
Writeback: 28 kB
AnonPages: 41260 kB
Mapped: 25696 kB
Shmem: 464 kB
Slab: 5056 kB
SReclaimable: 1880 kB
SUnreclaim: 3176 kB
KernelStack: 1232 kB
PageTables: 1040 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
WritebackTmp: 0 kB
CommitLimit: 252352 kB
Committed_AS: 347144 kB
VmallocTotal: 385024 kB
VmallocUsed: 3772 kB
VmallocChunk: 377388 kBIch hab die sd komplett neu installiert aber es wird nur 256 angezeigt was mach ich falsch kann mir jemand eine Anleitung geben nochmal
Danke schon im voraus -
So habe ich es gemacht:
- Raspbian downloaden und auf die SD-Karte übertragen
- System mit "raspi-config" initialisieren
- Raspbian aktuallisieren
- Firmware aktuallisieren mit "rpi-update"
https://github.com/Hexxeh/rpi-update
- Memory-Splitt (gpu_mem=XX) in folgender Datei anpassen
- neustarten
- Raspbian downloaden und auf die SD-Karte übertragen
-
Bei mir steht immer
raspi-config: command not found
rpi-update: command not foundund das steht in meiner config:
arm_freq=800
force_turbo=1
gpu_mem_256=128
gpu_mem_512=256was nun?
-
RPI-Update musst du erst installieren..
Einen Link findest du auch hier im Trend weiter oben
Gesendet von meinem GT-I9300 mit Tapatalk 2
-
das habe ich ja gemacht habe das eingegeben:sudo apt-get update && sudo apt-get upgrade dann lädt er was:
8 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
Need to get 7458 kB of archives.
After this operation, 64.5 kB of additional disk space will be used.
Do you want to continue [Y/n]?Das beantwort ich mit Y dann fängt er an zu downloaden und zu installieren danach gebe ich
raspi-config ein und da kommt dann halt
raspi-config: command not foundWas ist da los? ich bin bald am verzweifeln
-
Nur weil du für das OS die Updates installiert hast heist es nicht das dadurch auf software installiert wird ...
Wie ich schon geschrieben habe musst du rpi-update erst einmal installieren... hier der LINK zur Software und Anleitung
zusätzlich musst du noch git-core installieren
-
da kommt dann das:
pi@raspbmc:~$ rpi-update
This tool must be run as root
pi@raspbmc:~$
Ich glaub jetzt hat er das update gemacht hier mal die info:pi@raspbmc:~$ cat /proc/meminfo
MemTotal: 254124 kB
MemFree: 86220 kB
Buffers: 31392 kB
Cached: 95072 kB
SwapCached: 0 kB
Active: 70152 kB
Inactive: 86480 kB
Active(anon): 30520 kB
Inactive(anon): 108 kB
Active(file): 39632 kB
Inactive(file): 86372 kB
Unevictable: 0 kB
Mlocked: 0 kB
SwapTotal: 124924 kB
SwapFree: 124924 kB
Dirty: 0 kB
Writeback: 0 kB
AnonPages: 30180 kB
Mapped: 23048 kB
Shmem: 464 kB
Slab: 7368 kB
SReclaimable: 3820 kB
SUnreclaim: 3548 kB
KernelStack: 1216 kB
PageTables: 1008 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
WritebackTmp: 0 kB
CommitLimit: 251984 kB
Committed_AS: 321072 kB
VmallocTotal: 385024 kB
VmallocUsed: 3772 kB
VmallocChunk: 377388 kBpi@raspbmc:~$ free -m
total used free shared buffers cached
Mem: 248 163 84 0 30 92
-/+ buffers/cache: 40 207
Swap: 121 0 121 -
-
Hallo,
mein RPI fährt jetzt wieder hoch. Ich habe den Split 128 GPU
Und 128 CPU.
Mein Problem:
Eigentlich hat der CPU irgendwas mit 300.(Wegen 512mb RAM)
Kann mir jemand helefen? -
Mein Problem:
Eigentlich hat der CPU irgendwas mit 300.(Wegen 512mb RAM)
Kann mir jemand helefen?..
Verstehe dein Problem gerade nicht ganz ...
Da mittlerweile das FW Update Tool rpi-update aktualisiert wurde, würde ich dir empfehlen dies zu installieren. Den Link findest du hier im Thread (Beitrag 34 LINK )
-
Hallo zusammen,
ich habe jetzt auch mal veruscht meinen Rapsberry Pi ein update zu verpassen aber ich kommen nicht weiter.
Als erstes habe ich das gemacht:
Danach kam das alles:
Code1. sudo wget http://goo.gl/1BOfJ -O /usr/bin/rpi-update && sudo chmod +x /usr/bin/rpi-update 2. sudo apt-get install ca-certificates 3. sudo rpi-update
dann kriege ich die meldung das in der config.txt noch nichts eingetragen ist von wegen memorysplitt
also gucke ich in die Config.txt weis aber nicht was ich da jetzt eintragen soll.Meine Config.txt
Zitat# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4# uncomment for composite PAL
#sdtv_mode=2#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800# for more options see http://elinux.org/RPi_config.txt
Wär echt cool wenn ihr mir helfen könntet da ich gern die 512mb ram nutzen würde.
gruß prace07
EDIT: Da ich mich noch nicht so auskenne könnte mir bitte jemand den Terminal befehl geben wo ich cpu & meminfo auslesen kann?
-
Einfach "gpu_mem=16" in ne leere Zeile eintragen, oder halt 32, 64 128 oder 256
-
Danke für die schnelle antwort
habe jetzt gpu_mem=256 eingetragen und wollte dann über
bei memory_split auf 256 ARM und 256 GPU schalten aber da steht nur
128 ARM und 128 GPU also das ist das höchste dort.
Habe ich i-was vergessen zu machen oder warum zeigt der mir nichts an:Meine Config.txt sieht jetzt so aus:
Zitat# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720#gpu_mem=256 <--- Hoffentlich ist das Richtig so
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4# uncomment for composite PAL
#sdtv_mode=2#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800# for more options see http://elinux.org/RPi_config.txt
-
die # muss weg vor gpu_mem und wenn er immer noch n split von 128/128 hat stimmt aber immer noch was mit den Einstellungen oder der Firmware nicht.
-
Vielen Dank,
ich kann es leider nicht ausprobieren weil ich im Urlaub bin. -
-
Sieht so aus
Gesendet von meinem GT-I9300 mit Tapatalk 2
-
Seit dem 28.10. ist ein Raspbian draußen mit 512MB Unterstützung, inkl. angepasster raspi-config
-
Hallo,
Ich habe mir auch einen Rpi mit 512 MB bestellt.
Wenn ich ein Firmwareupdate mache, wird es auf einem Chip gespiechert/ geflashed, oder muss ich bei jeder neuinstallation des OS wieder das Firmwarupdate durchführen?
-
Jetzt mitmachen!
Du hast noch kein Benutzerkonto auf unserer Seite? Registriere dich kostenlos und nimm an unserer Community teil!