Wlan Problem pi3
-
AdolarB -
23. Oktober 2017 um 16:42 -
Erledigt
Heute ist Stammtischzeit:
Jeden Donnerstag 20:30 Uhr hier im Chat.
Wer Lust hat, kann sich gerne beteiligen. ;)
Jeden Donnerstag 20:30 Uhr hier im Chat.
Wer Lust hat, kann sich gerne beteiligen. ;)
-
-
Wlan Problem pi3? Schau mal ob du hier fündig wirst!
-
-
leider keine Änderung:
ifconfig:
-
leider keine Änderung:
Wie ist jetzt die Ausgabe von:
Hast Du evtl. einen Repeater, Hotspot, etc. (... mit der identischen SSID wie der AP/WLAN-Router) in deiner WLAN-Konstellation?
EDIT:
BTW: Die Ausgabe von "ifconfig" ist nicht relevant, denn die Herstellung einer funktionierenden WLAN-Verbindung bedeutet noch nicht, dass das Interface (hier wlan0), damit bzw. dadurch auch schon eine IP-Adresse zugewiesen bekommt.
Dann besser, die Ausgabe von:
EDIT2:
Poste mal auch aus der Ausgabe von:
den vollständigen Teil, der dein WLAN betrifft.
-
Vllt fehlt auch nur ein Bindestrich bei der ssid in der wpa_supplicant.conf
12. ssid=’heyn7390’ (aus config-File)
238,240 SSID heyn-7390 (aus Scan - 2 Mac Adressen)
Servus !
-
Code
sudo wpa_supplicant -i wlan0 -Dnl80211 -c /etc/wpa_supplicant/wpa_supplicant.conf -dCode
Alles anzeigen~ $ sudo wpa_supplicant -i wlan0 -Dnl80211 -c /etc/wpa_supplicant/wpa_supplicant.conf -d wpa_supplicant v2.4 random: Trying to read entropy from /dev/random Successfully initialized wpa_supplicant Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'nl80211' ctrl_interface 'N/A' bridge 'N/A' Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' country='DE' ctrl_interface='DIR=/var/run/wpa_supplicant GROUP=netdev' update_config=0 Priority group 0 id=0 ssid='heyn7390' rfkill: initial event: idx=1 type=2 op=0 soft=0 hard=0 rfkill: initial event: idx=4 type=1 op=0 soft=0 hard=0 nl80211: TDLS supported nl80211: Supported cipher 00-0f-ac:1 nl80211: Supported cipher 00-0f-ac:5 nl80211: Supported cipher 00-0f-ac:2 nl80211: Supported cipher 00-0f-ac:4 nl80211: Using driver-based off-channel TX nl80211: Supported vendor command: vendor_id=0x1018 subcmd=1 nl80211: Use separate P2P group interface (driver advertised support) nl80211: use P2P_DEVICE support nl80211: interface wlan0 in phy phy0 nl80211: Set mode ifindex 6 iftype 2 (STATION) nl80211: Subscribe to mgmt frames with non-AP handle 0x10758a0 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=040a nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 04 0a nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=040b nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 04 0b nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=040c nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 04 0c nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=040d nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 04 0d nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=090a nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 09 0a nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=090b nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 09 0b nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=090c nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 09 0c nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=090d nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 09 0d nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=0409506f9a09 nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=6): 04 09 50 6f 9a 09 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=7f506f9a09 nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=5): 7f 50 6f 9a 09 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=0801 nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 08 01 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=040e nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 04 0e nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=06 nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=1): 06 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=0a07 nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 0a 07 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=0a11 nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 0a 11 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=1101 nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 11 01 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=1102 nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 11 02 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x10758a0 match=0505 nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 05 05 nl80211: Failed to register Action frame processing - ignore for now netlink: Operstate: ifindex=6 linkmode=1 (userspace-control), operstate=5 (IF_OPER_DORMANT) nl80211: driver param='(null)' Add interface wlan0 to a new radio phy0 nl80211: Regulatory information - country=DE (DFS-ETSI) nl80211: 2400-2483 @ 40 MHz 20 mBm nl80211: 5150-5250 @ 80 MHz 20 mBm (no outdoor) nl80211: 5250-5350 @ 80 MHz 20 mBm (no outdoor) (DFS) nl80211: 5470-5725 @ 160 MHz 26 mBm (DFS) nl80211: 5725-5875 @ 80 MHz 13 mBm nl80211: 57000-66000 @ 2160 MHz 40 mBm nl80211: Added 802.11b mode based on 802.11g information wlan0: Own MAC address: b8:27:eb:86:6f:bb wpa_driver_nl80211_set_key: ifindex=6 (wlan0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=6 (wlan0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=6 (wlan0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=6 (wlan0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=6 (wlan0) alg=0 addr=(nil) key_idx=4 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=6 (wlan0) alg=0 addr=(nil) key_idx=5 set_tx=0 seq_len=0 key_len=0 wlan0: RSN: flushing PMKID list in the driver nl80211: Flush PMKIDs TDLS: TDLS operation supported by driver TDLS: Driver uses internal link setup TDLS: Driver does not support TDLS channel switching wlan0: WPS: UUID based on MAC address: afcadbfd-3e1c-573f-8e88-1a81484acc08 ENGINE: Loading dynamic engine ENGINE: Loading dynamic engine EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: Supplicant port status: Unauthorized nl80211: Skip set_supp_port(unauthorized) while not associated EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED Using existing control interface directory. ctrl_interface_group=108 (from group name 'netdev') ctrl_iface bind(PF_UNIX) failed: Address already in use ctrl_iface exists and seems to be in use - cannot override it Delete '/var/run/wpa_supplicant/wlan0' manually if it is not used anymore Failed to initialize control interface 'DIR=/var/run/wpa_supplicant GROUP=netdev'. You may have another wpa_supplicant process already running or the file was left by an unclean termination of wpa_supplicant in which case you will need to manually remove this file before starting wpa_supplicant again. Failed to add interface wlan0 wlan0: Request to deauthenticate - bssid=00:00:00:00:00:00 pending_bssid=00:00:00:00:00:00 reason=3 state=DISCONNECTED TDLS: Tear down peers wlan0: State: DISCONNECTED -> DISCONNECTED nl80211: Set wlan0 operstate 0->0 (DORMANT) netlink: Operstate: ifindex=6 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT) EAPOL: External notification - portEnabled=0 EAPOL: External notification - portValid=0 wlan0: WPA: Clear old PMK and PTK wlan0: Cancelling delayed sched scan wlan0: Cancelling scan request wlan0: Cancelling authentication timeout Remove interface wlan0 from radio phy0 Remove radio phy0 nl80211: deinit ifname=wlan0 disabled_11b_rates=0 nl80211: Remove monitor interface: refcount=0 netlink: Operstate: ifindex=6 linkmode=0 (kernel-control), operstate=6 (IF_OPER_UP) nl80211: Set mode ifindex 6 iftype 2 (STATION) nl80211: Unsubscribe mgmt frames handle 0x898fd029 (mode change)
Hast Du evtl. einen Repeater, Hotspot, etc. (... mit der identischen SSID wie der AP/WLAN-Router) in deiner WLAN-Konstellation?
Ja, mehrere:
Die 7390 hat einen Repeater mit gleicher SSID und einen RT-AC68 auch mit einem Repeater mit gleichnamiger SSID.....
bisher hat sich daran aber noch kein Gerät gestoßen.
iwconfig
Codeiwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11 ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=31 dBm Retry short limit:7 RTS thr:off Fragment thr:off Power Management:on
sudo iwlist wlan0 scan
Code
Alles anzeigen~ $ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11 ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=31 dBm Retry short limit:7 RTS thr:off Fragment thr:off Power Management:on pi@raspi-ch:~ $ ^C pi@raspi-ch:~ $ sudo iwlist wlan0 scan wlan0 Scan completed : Cell 01 - Address: C0:25:06:38:06:3B Channel:1 Frequency:2.412 GHz (Channel 1) Quality=55/70 Signal level=-55 dBm Encryption key:on ESSID:"heyn-7390" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=0000000000000000 Extra: Last beacon: 80ms ago IE: Unknown: 00096865796E2D37333930 IE: Unknown: 010882848B960C121824 IE: Unknown: 030101 IE: Unknown: 0706444520010D14 IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: 2D1ACE111BFFFF000000000000000000000100000000000000000000 IE: Unknown: 3D1601051700000000000000000000000000000000000000 IE: Unknown: 4A0E14000A002C01C800140005001900 IE: Unknown: 7F080100000000000040 IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0C00040E010102010000000000 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Cell 02 - Address: C2:25:06:38:06:3B Channel:1 Frequency:2.412 GHz (Channel 1) Quality=54/70 Signal level=-56 dBm Encryption key:on ESSID:"heyn Gastzugang" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=0000000000000000 Extra: Last beacon: 80ms ago IE: Unknown: 000F6865796E20476173747A7567616E67 IE: Unknown: 010882848B960C121824 IE: Unknown: 030101 IE: Unknown: 0706444520010D14 IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: 2D1ACE111BFFFF000000000000000000000100000000000000000000 IE: Unknown: 3D1601051700000000000000000000000000000000000000 IE: Unknown: 4A0E14000A002C01C800140005001900 IE: Unknown: 7F080100000000000040 IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0C00040E010102010000000000 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Cell 03 - Address: BC:EE:7B:DE:BD:18 Channel:13 Frequency:2.472 GHz (Channel 13) Quality=36/70 Signal level=-74 dBm Encryption key:on ESSID:"heyn-68U" Bit Rates:5.5 Mb/s; 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s Mode:Master Extra:tsf=0000000000000000 Extra: Last beacon: 80ms ago IE: Unknown: 00086865796E2D363855 IE: Unknown: 01088B9618243048606C IE: Unknown: 03010D IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: 32020C12 IE: Unknown: 0B050200220000 IE: Unknown: 2D1AEF1917FFFFFF0001000000000000000000000000000000000000 IE: Unknown: 3D160D0F1600000000000000000000000000000000000000 IE: Unknown: 7F080400080000000040 IE: Unknown: DDAE0050F204104A0001101044000102103B00010310470010CFC51D10A274A0D7C3492D48117C858D102100154153555354654B20436F6D707574657220496E632E1023001C57692D46692050726F74656374656420536574757020526F757465721024000852542D41433638551042001162633A65653A37623A64653A62643A31381054000800060050F20400011011000852542D4143363855100800022008103C0001011049000600372A000120 IE: Unknown: DD090010180202001C0000 IE: Unknown: DD180050F2020101840003A4000027A4000042435E0062322F00 IE: Unknown: 46057208010000 IE: Unknown: DD1F00904C0408BF0CB259820FEAFF0000EAFF0000C005000B000000C303010202 Cell 04 - Address: 28:6C:07:8B:43:0D Channel:1 Frequency:2.412 GHz (Channel 1) Quality=57/70 Signal level=-53 dBm Encryption key:on ESSID:"heyn-7390" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s 18 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 12 Mb/s; 24 Mb/s; 48 Mb/s Mode:Master Extra:tsf=0000000000000000 Extra: Last beacon: 80ms ago IE: Unknown: 00096865796E2D37333930 IE: Unknown: 010882848B961224486C IE: Unknown: 030101 IE: Unknown: 32040C183060 IE: Unknown: 0706434E20010E14 IE: Unknown: 33082001020304050607 IE: Unknown: 33082105060708090A0B IE: Unknown: 050400010000 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK IE: Unknown: DD310050F204104A0001101044000102104700102880288028801880A880286C078B430D103C0001011049000600372A000120 IE: Unknown: 2A0104 IE: Unknown: 2D1A6E1017FFFF000001000000000000000000000000000000000000 IE: Unknown: 3D1601050600000000000000000000000000000000000000 IE: Unknown: 4A0E14000A002C01C800140005001900 IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 IE: Unknown: 0B05020000127A IE: Unknown: DD07000C4300000000 Cell 05 - Address: 34:CE:00:14:66:69 Channel:13 Frequency:2.472 GHz (Channel 13) Quality=27/70 Signal level=-83 dBm Encryption key:on ESSID:"heyn-68U" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s 18 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 12 Mb/s; 24 Mb/s; 48 Mb/s Mode:Master Extra:tsf=0000000000000000 Extra: Last beacon: 80ms ago IE: Unknown: 00086865796E2D363855 IE: Unknown: 010882848B961224486C IE: Unknown: 03010D IE: Unknown: 2A0104 IE: Unknown: 32040C183060 IE: Unknown: 2D1A6E1017FFFF000001000000000000000000000000000000000000 IE: Unknown: 3D160D070600000000000000000000000000000000000000 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK IE: Unknown: 7F080000000000000000 IE: Unknown: 0B05020000127A IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 IE: Unknown: 4A0E14000A002C01C800140005001900 IE: Unknown: 0706434E20010E10 IE: Unknown: DD910050F204104A0001101044000102103B000103104700102880288028801880A88034CE001466691021001852616C696E6B20546563686E6F6C6F67792C20436F72702E10230003523032102400065254323836301042000831323334353637381054000800060050F20400011011000C5869616F4D69526F7574657210080002210C103C0001011049000600372A000120 IE: Unknown: DD07000C4300000000
-
Code
ctrl_iface bind(PF_UNIX) failed: Address already in use ctrl_iface exists and seems to be in use - cannot override it Delete '/var/run/wpa_supplicant/wlan0' manually if it is not used anymore Failed to initialize control interface 'DIR=/var/run/wpa_supplicant GROUP=netdev'. You may have another wpa_supplicant process already running or the file was left by an unclean termination of wpa_supplicant in which case you will need to manually remove this file before starting wpa_supplicant again.
Mach mal:
und danach:
EDIT:
Poste mal auch die Ausgaben von:
Codesudo cat /etc/wpa_supplicant/wpa_supplicant.conf | grep -i ssid sudo iwlist wlan0 scan | grep -i essid
EDIT 2:
Von wegen nur WPA2:
CodeIE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK
... lt. der Ausgabe von "iwlist".
-
sudo cat /etc/wpa_supplicant/wpa_supplicant.conf | grep -i ssid
sudo iwlist wlan0 scan | grep -i essid
Code$ sudo iwlist wlan0 scan | grep -i essid wlan0 Interface doesn't support scanning : Device or resource busy
Von wegen nur WPA2:
Fb steht auf: WPA2 (CCMP)
Soll ich die Repeater mal deaktivieren?
-
Brauchst/willst Du jetzt keine Hilfe mehr?
-
Soll ich die Repeater mal deaktivieren?
Vorher vielleicht noch die ssid auf "heyn-7390" ändern, in der wpa_supplicant.conf
Servus !
-
Bitte?
Doch, ich würde gerne den RPi über Wlan ansprechen.
Ich entnehme deiner Aussage, daß mit dem geposteten Auszug was nicht stimmt?
Habe es noch einmal versucht, nun steht da folgendes:
Codesudo iwlist wlan0 scan | grep -i essid ESSID:"heyn-7390" ESSID:"heyn Gastzugang" ESSID:"heyn-68U" ESSID:"heyn-68U"
Warum beim ersten Mal mal busy gezeigt hat, weiß ich nicht. die Befehlszeile hatte ich mit hineinkopiert.
-
Vorher vielleicht noch die ssid auf "heyn-7390" ändern, in der wpa_supplicant.conf
Das war eine sehr gute Idee - ich schäme mich.
Leider aber noch das selbe. der Repeater mit der selben SSID ist jetzt aus
-
O.K., Danke an ALLE
was auch immer passiert ist, nun geht es. Ich was kurz weg und der RPi stromlos. Als ich wiederkam und ihn ansteckte, war er plötzlich auf der FB zu sehen. Nun hat er einen vorläufigen Platz außerhelb der Reichweite eines Kabels bekommen und lässt sich gut über Wlan ansprechen - über Repeater mit der selben SSID wie die FB.
Nochmals Dank für eure Mühe und Tips,
ein glücklicher
Adolar
-
Super! Dann bitte noch den Thread als erledigt markieren
-
-
Jetzt mitmachen!
Du hast noch kein Benutzerkonto auf unserer Seite? Registriere dich kostenlos und nimm an unserer Community teil!