Hallo zusammen,
bin an meinem Pi3B+ seit gestern mit dem UMTS Surfstick MF190 am kämpfen.
Und zwar bin ich nach folgender Anleitung vorgegangen:
https://wiki.siduction.de/index.php?titl…ilfe_von_wvdial
Hat soweit geklappt.
Hir mal ein paar Ein/Ausgaben:
root@raspberrypi:~# lsusb
Bus 001 Device 007: ID 19d2:0117 ZTE WCDMA Technologies MSM
Bus 001 Device 004: ID 1908:2310 GEMBIRD
Bus 001 Device 005: ID 0424:7800 Standard Microsystems Corp.
Bus 001 Device 003: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 001 Device 002: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@raspberrypi:~# ifconfig -a
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.178.16 netmask 255.255.255.0 broadcast 192.168.178.255
inet6 2003:eb:6f16:1200:f24b:47ca:715d:ea84 prefixlen 64 scopeid 0x0<global>
inet6 fe80::718d:aa6e:641a:1794 prefixlen 64 scopeid 0x20<link>
ether b8:27:eb:91:25:88 txqueuelen 1000 (Ethernet)
RX packets 1429 bytes 123573 (120.6 KiB)
RX errors 0 dropped 4 overruns 0 frame 0
TX packets 359 bytes 51269 (50.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Lokale Schleife)
RX packets 28320 bytes 45633766 (43.5 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 28320 bytes 45633766 (43.5 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether b8:27:eb:c4:70:dd txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Alles anzeigen
Hier steht noch KEIN Modem drin.
Jedoch bei:
root@raspberrypi:~# wvdialconf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyUSB1<*1>: ATQ0 V1 E1 -- OK
ttyUSB1<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB1<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB1<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB1<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB1<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB1<*1>: Modem Identifier: ATI -- Manufacturer: ZTE CORPORATION
ttyUSB1<*1>: Speed 9600: AT -- OK
ttyUSB1<*1>: Max speed is 9600; that should be safe.
ttyUSB1<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB2<*1>: Modem Identifier: ATI -- Manufacturer: ZTE CORPORATION
ttyUSB2<*1>: Speed 9600: AT -- OK
ttyUSB2<*1>: Max speed is 9600; that should be safe.
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
Found a modem on /dev/ttyUSB1.
Modem configuration written to /etc/wvdial.conf.
ttyUSB1<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
ttyUSB2<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
Alles anzeigen
Erhalte ich unter USB1 ein Modem.
root@raspberrypi:~# wvdial umts
--> WvDial: Internet dialer version 1.61
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Sending: AT+CGDCONT=1,"IP","web.vodafone.de"
AT+CGDCONT=1,"IP","web.vodafone.de"
OK
--> Modem initialized.
--> Sending: ATDT*99***1#
--> Waiting for carrier.
ATDT*99***1#
CONNECT 7200000
--> Carrier detected. Starting PPP immediately.
--> Starting pppd at Sun Dec 8 11:04:39 2019
--> Pid of pppd: 1637
--> Using interface ppp0
--> pppd: ▒▒[07][01]▒▒[07][01]
--> pppd: ▒▒[07][01]▒▒[07][01]
Alles anzeigen
Verbindung müsste aufgebaut werden.
Wenn ich jetzt das Netzwerkkabel ziehe habe ich seltsamerweise keine VNC Zugang mehr und auch ioBroker Cloud geht nicht, was eigentlich sein müsste.
Vielleicht klappt auch nicht die automatische Umschaltung von Netzwerk auf die UMTS Verbindung.
Also habe ich es mit direktem automatischen UMTS Aufbau versucht:
In /etc/network/interfaces folgendes hinzugefügt:
So, jetzt habe ich aber wieder kein VNC und auch keine ioBroker Cloud Verbindung.
Ich weiß auch nicht ob die Verbindung überhaupt steht, da Headless das Ganze.