Ich habe auf meinem RPi 4 seit langem den ioBroker erfolgreich am laufen. Das System bootet von externer USB-SSD. Nach einem fullupgrade ist der PI nicht mehr im Netz erreichbar. In der Fritzbox gilt er als inaktiv. Nach dem einschalten leuchtet sofort die rote LED mit der grünen auf, wobei die grüne LED dann noch einmal kurz aufblinkt und dann ausbleibt. Die LAN-Led zeigt auch keine Aktivitäten an.
Platform : linux
os : linux
Debian Version: 11.5
Architecture : arm
CPUs : 4
Speed : 1500 MHz
Model : ARMv7 Processor rev 3 (v7l)
RAM : 3.7 GB
Disk size : 284.4 GiB
Disk free : 258.1 GiB
Hier die letzten Aktionen die ich gemacht habe:
Code
markus@rpi:~ $ sudo apt update
[sudo] Passwort für markus:
OK:1 http://raspbian.raspberrypi.org/raspbian bullseye InRelease
OK:2 http://archive.raspberrypi.org/debian bullseye InRelease
OK:3 https://dl.yarnpkg.com/debian stable InRelease
OK:4 https://deb.nodesource.com/node_16.x bullseye InRelease
Paketlisten werden gelesen… Fertig
Abhängigkeitsbaum wird aufgebaut… Fertig
Statusinformationen werden eingelesen… Fertig
Aktualisierung für 13 Pakete verfügbar. Führen Sie »apt list --upgradable« aus, um sie anzuzeigen.
Code
markus@rpi:~ $ sudo apt full-upgrade
Paketlisten werden gelesen… Fertig
Abhängigkeitsbaum wird aufgebaut… Fertig
Statusinformationen werden eingelesen… Fertig
Paketaktualisierung (Upgrade) wird berechnet… Fertig
Die folgenden Pakete wurden automatisch installiert und werden nicht mehr benötigt:
alsa-base gstreamer0.10-alsa gstreamer0.10-plugins-base libbluetooth3 libcdio18 libgstreamer-plugins-base0.10-0
libgstreamer0.10-0 libnfs12 libxfconf-0-2 lxplug-volume pimixer point-rpi
Verwenden Sie »sudo apt autoremove«, um sie zu entfernen.
Die folgenden Pakete werden ENTFERNT:
bluealsa fuse libgc1c2 libpolkit-backend-1-0 raspberrypi-artwork
Die folgenden NEUEN Pakete werden installiert:
agnostics cups-pk-helper fio flashrom fuse3 gir1.2-notify-0.7 gir1.2-packagekitglib-1.0 gir1.2-polkit-1.0 gir1.2-secret-1
gui-pkinst ibverbs-providers libaio1 libboost-iostreams1.74.0 libboost-thread1.74.0 libcupsimage2 libftdi1-2 libfuse3-3 libgc1
libgfapi0 libgfrpc0 libgfxdr0 libglusterfs0 libibverbs1 libnma-common libnma0 libnuma1 librados2 librbd1 librdmacm1
lxplug-magnifier lxplug-menu lxplug-netman lxplug-updater lxplug-volumepulse pi-printer-support pixflat-icons
printer-driver-escpr pulseaudio-module-bluetooth python3-cups python3-cupshelpers python3-smbc python3-toml rp-bookshelf
rpi-eeprom system-config-printer system-config-printer-common system-config-printer-udev
Die folgenden Pakete werden aktualisiert (Upgrade):
guile-2.2-libs gvfs gvfs-backends gvfs-common gvfs-daemons gvfs-fuse gvfs-libs libpolkit-agent-1-0 libpolkit-gobject-1-0
policykit-1 raspberrypi-sys-mods raspberrypi-ui-mods raspi-config
13 aktualisiert, 47 neu installiert, 5 zu entfernen und 0 nicht aktualisiert.
Es müssen 31,3 MB an Archiven heruntergeladen werden.
Nach dieser Operation werden 78,8 MB Plattenplatz zusätzlich benutzt.
Möchten Sie fortfahren? [J/n] J
Holen:1 http://archive.raspberrypi.org/debian bullseye/main armhf policykit-1 armhf 0.105-31+rpt1+deb11u1 [91,5 kB]
....
....
....
Alles anzeigen
Es wurde alles ohne Fehlermeldungen oder Hinweise installiert.
Nach dem anschließenden reboot war der PI nicht mehr da.
Code
Hier noch einige Config Dateien:
/etc/fstab
proc /proc proc defaults 0 0
PARTUUID=02211fe5-01 /boot vfat defaults,flush 0 2
#PARTUUID=924c1207-02 / ext4 defaults,noatime 0 1
# a swapfile is not a swap partition, no line here
# use dphys-swapfile swap[on|off] for that
/dev/sdb1 / ext4 defaults,noatime 0 1
/dev/sdb2 swap swap defaults 0 0
/boot/cmdline.txt
dwc_otg.lpm_enable=0 console=serial0,115200 console=tty1 root=PARTUUID=924c1207-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles
/boot/config.txt
# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details
# pehr 20.09.2019 Eintrag hinzugefügt, dasss auch von USB-HDD gebootet werden kann
program_usb_boot_mode=1
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
# pehr 19.09.2019 Altes TV-Modell=2 Computer-Monitor=1
hdmi_group=2
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2
[all]
#dtoverlay=vc4-fkms-v3d
Alles anzeigen