Hallo,
Ich habe ein Skript geschrieben, welches libcamera-jpeg -o test.jpg ausführt.
Aber manchmal/ meistens crashed das Skript (warscheinlich stürzt der pi ab):
Code
[0:20:33.916495803] [579] INFO Camera camera_manager.cpp:293 libcamera v0.0.0+3156-f4070274
[0:20:34.269731293] [579] INFO Camera camera.cpp:937 configuring streams: (0) 1296x972-YUV420
[0:20:34.271511260] [581] INFO RPI raspberrypi.cpp:122 Mode: 2592x1944 fmt BG10 Score: 2067 (best 2067)
[0:20:34.272809236] [581] INFO RPI raspberrypi.cpp:122 Mode: 1920x1080 fmt BG10 Score: 1849.67 (best 1849.67)
[0:20:34.274432207] [581] INFO RPI raspberrypi.cpp:122 Mode: 1296x972 fmt BG10 Score: 1500 (best 1500)
[0:20:34.276211174] [581] INFO RPI raspberrypi.cpp:122 Mode: 640x480 fmt BG10 Score: 3796 (best 1500)
[0:20:34.277991141] [581] INFO RPI raspberrypi.cpp:122 Mode: 640x480 fmt BA81 Score: 4796 (best 1500)
[0:20:34.280470095] [581] INFO RPI raspberrypi.cpp:122 Mode: 2592x1944 fmt pBAA Score: 1567 (best 1500)
[0:20:34.282263062] [581] INFO RPI raspberrypi.cpp:122 Mode: 1920x1080 fmt pBAA Score: 1349.67 (best 1349.67)
[0:20:34.286347987] [581] INFO RPI raspberrypi.cpp:122 Mode: 1296x972 fmt pBAA Score: 1000 (best 1000)
[0:20:34.288111955] [581] INFO RPI raspberrypi.cpp:122 Mode: 640x480 fmt pBAA Score: 3296 (best 1000)
[0:20:34.288724943] [581] INFO RPI raspberrypi.cpp:620 Sensor: /base/soc/i2c0mux/i2c@1/ov5647@36 - Selected mode: 1296x972-pBAA
[0:20:34.432840290] [581] INFO RPISTREAM rpi_stream.cpp:122 No buffers available for ISP Output0
[0:20:34.434180265] [581] INFO RPISTREAM rpi_stream.cpp:122 No buffers available for ISP Output0
[0:20:34.435299245] [581] INFO RPISTREAM rpi_stream.cpp:122 No buffers available for ISP Output0
[0:20:34.436126229] [581] INFO RPISTREAM rpi_stream.cpp:122 No buffers available for ISP Output0
[0:20:34.545436217] [581] INFO RPI raspberrypi.cpp:1636 Dropping frame at the request of the IPA (7 left)
Alles anzeigen
Es stürzt auch ab, wenn ich den Kommand im Terminal ausführe.
Die Kamera:
Ich weiß nicht, ob das wirklich die Kamera ist, aber es ist die gleiche Art von Kamera:
Meine boot/config.txt:
Code
# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
# Automatically load overlays for detected cameras
camera_auto_detect=1
# Automatically load overlays for detected DSI displays
display_auto_detect=1
# Enable DRM VC4 V3D driver
dtoverlay=vc4-kms-v3d
max_framebuffers=2
# Disable compensation for displays with overscan
disable_overscan=1
[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
otg_mode=1
[all]
[pi4]
# Run as fast as firmware / board allows
arm_boost=1
[all]
Alles anzeigen